Course syllabus

MEN120 Heat and power systems engineering lp1 HT24 (7.5 hp)

Link to weekly overview of course activities

Course is offered by the department of Space, Earth and Environment

_____________________________________________________________________

To mitigate climate change, and to work towards a more sustainable society, actions are needed across all sectors e.g. including agriculture, industry and transportation. The focus for this course is on thermal heat and power production plants. Even though the share of renewable power production has increased, the fossil-based power plants are, both globally and from a European perspective, still responsible for the main share of power production. The high share of intermittent sources has, however, caused changes in operational patterns of thermal power plants. Thermal power plants originally designed for base load power generation will now need to act as top load plants. As top load plants they have to ramp up and down to follow the demand. Combined cycle thermal power plants might even need to start-up and shut down on daily basis or several times over the course of a week, even if they were conceived for base load generation. Therefore, flexible and transient operation is becoming of increasing importance in thermal power generation. Such a transient operation will have a huge influence on the performance of the plant affecting efficiency as well as emissions.

Switching from coal to biogenic and waste derived fuels are one of the proposed ways to reduce CO₂ emissions from power generation and industrial furnaces. Due to the different composition between coal and these other fuels, it is, however, not only a question of switching fuel, but also how to handle the problems that arise. One such problem is the high temperature corrosion (HTC) which is a problem that affects the heat transfer surfaces in a boiler. HTC is caused mainly by alkali-based salts that easily are deposited on heat transfer surfaces and are also corrosive. Compounds that contain alkali metals and chlorine are among the most aggressive agents, which is why HTC is primarily a problem for power plants that are fired with bio- and waste-fuels rather than coal.

A second alternative to significantly reduce CO₂ emissions is to apply carbon capture where the CO₂ is separated from the flue gas and later used or stored to prevent it to be emitted to the atmosphere. An interesting alternative is to combine combustion of biogenic fuels and carbon capture which has the potential to reduce the atmospheric CO₂ concentration. The capture part can be performed in different ways but always comes with an extra energy requirement reducing the efficiency and increasing the investment and operational cost compared to not applying carbon capture.

A significant effort is required in the heat and power production sector to be able to adopt to the new situation it is facing and at the same time keep emissions like SO_X, NO_X and particulates below emission limits during a transition phase towards zero emission control systems, that is, systems that are not yet commercially adopted. The plant design is important in order to find solutions. In this course the design opportunities of modern power plants will be discussed as well as the potential of modernizing older power plants. This is done by looking into the design of coal, natural gas and waste or biomass based combined heat and power plants. Their similarities and differences will be discussed from a thermodynamic point of view. Theoretical knowledge gained will then be applied in a project work, consisting of simulations of these different power plants. When building different models, the students will be able to see how the performance of a power plant changes by, for example, adding a carbon capture unit or switching fuel from coal to biomass. Combined with the theoretical background given during lectures the student will also understand why the power plant behaves in a certain way and be able to evaluate different thermal power plants with respect to overall performance, regional energy system and emission regulations.

Course administration

MEN120 Heat and power systems engineering (7.5 hp) is given in lp1 by the division of Energy Technology at the department of Space, Earth and Environment. Lecture notes and other relevant material will be distributed via the course homepage in Canvas. The course page is also used as the platform for hand-ins.

Contact details                           

Fancisco Javier Triana De Las Heras                javiertr@chalmers.se

Saumitra Mishra                                                mishrasa@chalmers.se

Johanna Beiron                                                  beiron@chalmers.se

Kushagra Gupta                                                 kushagra.gupta@chalmers.se

Sven Andersson                                                 sveander@chalmers.se

Thomas Allgurén                                                thomas.allguren@aeec.se

Lars Strömberg                                                   lob.stromberg@telia.com

Klas Andersson (Examiner)                                klon@chalmers.se 

Course purpose

The purpose of this course is to give students a good insight into power plant engineering. The course focuses on production of heat and electric power in thermal power plants. Students will also get an overview on how such plants fit into the energy system, including aspects on distribution of heat and electricity as well as principles of the electricity market. After completing the course, students will be able to perform a thorough analysis of the efficiency and environmental performance of a Combined Heat and Power (CHP) plant. In addition, students will be able to use a state-of-the-art process simulation tool to evaluate the performance of thermal power plants.

Schedule

See Schedule document posted in the files section on Canvas.

Course literature

The course literature include material handed out during the lectures, Case study material as well as other electronic material.

Course structure

There are three parts of the course, lectures, problem solving sessions and the case study which is a group exercise. The lectures comprises theory and engineering knowledge looking on design aspects of thermal power plants using solid and gaseous fuels as feed stock; renewable and fossil. The main components of steam and combined cycle power plants are presented in lectures and further studied based on hand calculations during the problem-solving sessions. Lectures and problem-solving sessions will give the student a theoretical understanding of the differences between different power plant configurations from a thermodynamic point of view as well as with respect to emissions. Lectures are given according to the provided schedule with the different topics specified. The problem-solving sessions will also follow given schedule and reflect on what has been discussed during recent lectures.

The third part, the case study, is performed by the students in groups with two students. The case study includes modeling of thermal heat and power plants using a commercial software (EBSILON®Professional), which is a state-of-the-art process modelling tool. The simulation tool makes it possible to compare different designs and concepts for thermal power generation. In this way the students have a possibility to further evaluate and analyze what has been discussed during lectures and problem-solving sessions gaining a deeper understanding of the theory and how it links to the design of an actual power plant. The simulated plant will be inspired by real actual power plants. There are several hours scheduled for the students to work with the case study with teachers available for supervision. The case study will be supervised by the course assistants. The students are expected to also work with the case study outside of these computer-sessions and the software will be available in several computer rooms at Chalmers. The case study project runs throughout the course and consist one introduction exercise and modeling of plants designed for municipal solid waste and natural gas. Each part will have its own individual hand-ins and also be summarized in an oral presentation and discussion session towards the end of the course.

Lecture material, example problems, case study instructions etc will be available to download from the Canvas home page. All hand ins will also be submitted via Canvas. General information from the teachers to all students will be provided via Canvas and e-mail. Individual communication between teachers and students, e.g. a student having a question regarding a modelling problem, should however be done via e-mail.

Learning objectives and syllabus

At the end of this course, students should be able to analyze and evaluate new heat and power plants. After completing the course, students will be aware of the technological options and environmental problems and opportunities associated with these options. The main generic skills developed within this course include the ability to apply thermodynamics to thermal processes for heat and electric power generation and to analyze opportunities for investment in a new CHP plant in an existing energy system. Specific learning outcomes are as follows:

• To know the main technological options for generation of heat and power, including both existing technologies as well as new technologies in the development stage
• To be able to perform thermodynamic analysis of thermal power plants in different design modes
• To be able to analyze the environmental impact from different types of power plants and to know which cleaning technologies to apply
• To be able to use a state-of-the-art process simulation tool in order to establish the process flowsheet schematic of a CHP plant and to determine the performance of the plant.

Examination form

To pass the course (grade 3) the student must; participate and give oral presentations in the beginning and at the end of the course, have all case study reports approved and score at least 12 out of 24 points on the written exam. The written exam also provides the opportunity to get grade 4 or 5 with a score of at least 16 or 20 points respectively. Once all compulsory parts are approved the student will be given the same grade on the course as he or she received on the written exam. The written exam consists of one theory and one calculation section with the total point divided equally between the two sections. Examples of previous exams will be provided during the course. Steam and air properties tables will be handed out during the written exam if needed. In addition, Mollier chart and calculator with cleared memory are allowed aids during the written exam.